Hot
-16%

Launch X431 PAD V New Version Auto Full System Diagnostic OBD Tool, 21+ Free Online Programming Car Brands + J2534 ECU Online Programming, +50 Special Functions ADAS Online Codding CAN FD DoiP etc

$1,950.09

  • Official 100% Genuine Autel Launch ThinkCar Tools
  • Free Import Tax (European-USA-UK-Australian-Russia Warehouse)
  • Fast Shipment 3-5 days DHL or UPS
  • 2 Years Free Updates
SKU: X431 PAD V Category: Tag:

Description

LAUNCH X431 PAD V (Global Version)

Top Reason to Choose LAUNCH X431 PAD V

Free 21 Car Brands ECU Online Programming OBD2 Scanner: LAUNCH X431 PAD V can program the ECU of Audi, BMW, Porsche, Mercedes-Benz, Volkswagen, Land Rover(Jaguar), Nissan, Skoda, SEAT, Subaru, Kia, Hyundai, Renault, Ford, Mini, Shanghai VW, FAW-VW, GAC MOTOR, Chery, EXEED, and MG cars. What’s more, support VW, Audi, BMW, Porsche and Benz cars’ manual ECU programming, even if automatic ECU programming fails, it can be reprogrammed! ,  Now Ford cars need to switch to Chinese to program!)

 

1. High configuration hardware: 10.1 inch Touchscreen, sun readable screen, protection grade IP65, more waterproof, more resistant to falling, and the vehicle can work normally after rolling

2. Support 5G Wi-Fi Diagnosis , 4GB RAM + 128GB ROM (can up to 256GB)

3. 2 Years Free Update besides, you can use all functions as normal after 2 years free update,it will not be locked

4. Online ECU Programming + Online Coding + J2354 Programming

5. OE-Level Full System Diagnosis + 50 More Reset Service

6. Support support Topological Graph + J2534/RP1210/D-PDU / CAN FD DolP New Protocols

7. Full Bi-Directiona Control / Active Test + ECU Coding + Guide Function

8. FCA AutoAuth Access + SCN Online Coding

9. 24 Language Support , No language barrier

10. Auto VIN Scan + Remote Diagnostic +Diagnostic Feedback +Maintenance records, ect

11. 5 Years Warranty + Free Tech Supports

12. Extended module: Compatible with Oscillograph, X-PROG 3, TSGUN Wand, RF-Sensor, BST360 Battery Test, VSP600 Videoscope, ADAS, 24V Heavy Duty software , Wi-Fi printer, New energy vehicle, Multimeter, Ignition analysis etc.

and more …

What situation needs to perform programming ?

1. Programming new ECUs: Replace new ECU(Determine if programming or coding is required based on fault code prompts). It can read and back up the original ECU data of the vehicle. (Note: The newly purchased spare part numbers need to be equal to the original ones.)

2. Reprogramming second-hand ECUs: Clear second-hand ECU data for reprogramming(if the second-hand has the anti-theft data, it needs to be used with LAUNCH X-PROG3 to clear anti-theft data first, and then match it with the original anti-theft data before reprogramming.).

3.Update the ECU: Some of the ECU has BUGs so it will cause some faults that are difficult to repair. ( For BMW 2889 DME intake valve, carbon deposition, and some of F serious machine oil lamps can’t be zero.)

4. Fixing lost data of ECU: When the software in the ECU corrupts the program due to battery or grounding issues(the Hardware is normal), re-programming can rectify it back to normal operation.

5. Reprogramming on failed programming ECU: If the programming fails but the hardware didn’t damage, the LAUNCH X431 PAD V can reprogram the module in Manual Mode which is compatible with VW/Audi/Ben/BMW. And it supports Programming Backup/Restoration that is applied to match anti-theft data for Mercedes-Benz engine modules and transmission modules, which requires purchasing X-431 PROG3 additionally (If the programming fails, ECU will not communicate and you will not be able to access the system ).

 

AutoAuth for FCA SGW

you will have access to the security gateway module on 2017 and newer Fiat/ Chrysler/ Dodge/ Jeep vehicles(2017-2022), so that the diagnostic tool can clear codes, run bi-directional active tests, actuations, relearns or even IMMO key programming (pulls PIN & write), ADAS calibration assistance etc.

(please note: FCA account needs to be purchased )

FCA official link : https://www.technicalinformation.fiat.com/tech-info-web/web/index.do?request_locale=en

Multi-Language Supports

Support English, French, Spanish, German, Russian, Korean, Japanese, Portuguese, Italian, Polish, Dutch, Hungarian, Finnish, Simplified, Czech, Turkish, Greek, Arabic, Danish, Persian, Romanian, Serbian, Swedish, Chinese Traditional
Language is free, switch at will

Highly recommended by auto repair shops and mechanics!!!

Compared with the programming products supported in the market, LAUNCH X431 PAD V supports more models and more comprehensive functions

a. Support 30+ Car Brands, overing European cars, American cars, Asian cars and Chinese cars ,and keep increating

b. function including:
Online Coding, Online Programming,Online Parametric Configuration,On-Line Matching And Calibration, Fuel Quality Defect Firmware Upgrade and more

c. Applicable vehicle models for online programming : For Mercedes Benz, for Porsche, for FAW Volkswagen, for Kia, for bmw, for Nissan, for SKODA, for Mazda ,for VW, for Beijing Hyundai, For Seat, for Fiat, for Audi, For SAIC Rongwei, for Renault, for China GM, For SAIC MG, for GAC MOTOR, for Ford, for Shanghai Volkswagen , for Hyundai, keep increasing…

Vehicle Programming Benefits

1.For Great Wall : support Great Wall, Haval (ECM/AT #), WEY, Oula

2.for Volkswagen Audi advantages: online programming (support for programming and resurrection), firmware upgrade for fuel quality defects, online parametric configuration, part number upgrade, support for manual programming ( more online codes, more online parametric configurations, more online matching and calibration)

3. for Benz advantages : manual control unit programming; clone.

4. for BMW advantages: the code setting data is up to March 22, and it supports modification. Brush hiding has function help, and brush hiding has expert mode.

5. for Mercedes Benz advantages : 13 years ago, it had initialization startup (programming, code setting, anti-theft, initialization). After 13 models, the engine module and transmission module can be cloned.

6. for Ford advantages: Since 2018, all models and functions of FORD original factory have been online.
Basic function: After 18 years, X-431 is offline
Special function: After 18 years, X-431 will be online
The original manufacturers of Chrysler and FIAT have gradually put all models and functions online since 2018. X-431 all functions online

What is Programming Function ? What different is Online Programming and Offline/J2534 Programming ?

Programming Function is to finish program/ rewrite/ code/ match new ECU after new module replacement. Taking your business to a new height, it can for :
1) program the new adaptive data to the on-board modules;
2) replace the existing software/firmware in the ECUs;
3) match the component control modules after repair or replacement;
4) flash the hidden functions and
5) enhance the vehicle performance.

Online Programming is download the original data from automaker service directly , it is ensures the correctness and latest version of the data you get , Improves the success rate of programming !!!

Offline/J2534 Programming is for you had the data , just write it to you ecu directly( if you do not have the data , you can not do programming function ).

LAUNCH X431 PAD V supports Online Programming + Offline/J2534 programming , it is more powerful and Cost-effective than other J2534 tool :

* X-431 PAD V online programming does not require an expensive online account, just connect to WIFI, saving maintenance costs.

* smartbox adopts dual WIFI communication to improve programming speed, thereby reducing the possibility of programming errors

* When using J2534 tool, in addition to the connector, it is also necessary to consider issues such as adapting the computer, installation costs, and complete functions, which is not cost-effective.

Support J2534, DolP, CAN FD and other protocols with SmartLink C connector

J2534 / RP1210 Diagnostic Protocols Cover More Vehicle Type,you can perform OE-level diagnosis and programming for more accurate diagnosis and efficient car repair jobs to win more business!

DoIP/CAN FD Protocols for High-Speed CAN Cover New Vehicle Models

 

50+ HOT Services. Handle Your Daily Car Maintenance.

1. Oil Reset Service

reset the oil service for the engine oil life system, which calculates an optimal oil life change interval depending on the vehicle driving conditions and weather events.It needs to be performed in the following cases:
1. If the service lamp is on, run car diagnostics first for troubleshooting. After that, reset the driving mileage or driving time, so as to turn off the service lamp and enable a new driving cycle.
2. If the service lamp is not on, but you have changed the engine oil or electric appliances that monitor oil life, you need to reset the service lamp.

2. Electronic Parking Brake Reset

reset the brake pad after replacing the brake pad.It needs to be performed in the following cases:
1. The brake pad and brake pad wear sensor are replaced.
2. The brake pad indicator lamp is on.
3. The brake pad sensor circuit i
3 Steering Angle Calibration
reset the steering angle, after replacing the steering angle position sensor, replacing steering mechanical parts (such as steering gearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recovering car body

4. ABS Bleeding

perform various bi-directional tests to check the operating conditions of Anti-lock Braking System (ABS). It needs to be performed in the following cases:
1. When the ABS contains air.
2. When the ABS computer, ABS pump, brake master cylinder, brake cylinder, brake line, or brake fluid is replaced.

5. Tire Pressure Monitor System Reset

quickly look up the tire sensor IDs from the vehicle’s ECU, reset tire pressure and turn off the tire pressure MIL. It needs to be performed in the following cases: Tire pressure is too low, tire leaks, tire pressure monitoring device is replaced or installed, tire is replaced, tire pressure sensor is damaged, and tire is replaced for the car with tire pressure monitoring function.

6 .Gear Learning

perform tooth learning for the car, to turn off the MIL. It needs to be performed in the following cases:
1. After the engine ECU, crankshaft position sensor, or crankshaft flywheel is replaced.
2. The DTC ‘tooth not learned’ is present.

7. Injector Coding

write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder, so as to more accurately control or correct cylinder injection quantity. It needs to be performed in the following cases: After the ECU or injector is replaced.


8 . Battery Maintenance System Reset

perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done. It needs to be performed in the following cases:
1. The main battery is replaced.
2. The battery monitoring sensor is replaced.

9. Diesel Particulate Filter (DPF) Regeneration

clear PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance. It needs to be performed in the following cases:
1. The exhaust back pressure sensor is replaced.
2. The PM trap is removed or replaced.
3. The fuel additive nozzle is removed or replaced.
4. The catalytic oxidizer is removed or replaced.
5. The DPF regeneration MIL is on and maintenance is performed.
6. The DPF regeneration control module is replaced.

10. Electronic Throttle Position Reset

make initial settings to throttle actuators and returns the learned values stored on ECU to the default state. Doing so can accurately control the actions of regulating throttle (or idle engine) to adjust the amount of air intake.
11 EGR Adaption
learn the EGR (Exhaust Gas Recirculation) valve after it is cleaned or replaced.

12 .Gearbox Matching

This function can complete the self-learning of the gearbox and improve the shift quality. It needs to be performed in the following cases: When the gearbox is disassembled or repaired.

13 .AdBlue Reset (Diesel Engine Exhaust Gas Filter)

After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea
reset operation is required.

14 .Transport Mode

To lower vehicle power consumption, user may perform the following operations: limit vehicle speed, not wake up the network for door open and disable remote key etc. In this case, deactivating transport mode is needed to recover vehicle being normal.

15. Windows Calibration

perform door window matching to recover the ECU initial memory, and recover the automatic ascending and descending function of power window.

and More …

Work with X431 X-PROG3 to do anti-theft matching, anti-theft programming (Optional)

★Fast and accurate reading and writing of data.

★ Powerful functions, supporting Mercedes-Benz infrared key reading/writing, BMW engine ISN code reading, engine reading in BENCH mode, etc.

Functions
★Read BMW engine ISN code.
★Read/write BMW CAS4+ and FEM chips.
★Read/write Audi fifth-generation steering column chipsH3.Read/write Audi fifth-generation steering column chips.
★Read/write EEPROM.
★Read/write MCU.
★VW Fourth-generation Dump Mode All Keys Lost.
★Read engine in BENCH mode.
★ Read gearbox data.
★More features are constantly updated………

Guided Functions for VW and for Audi Brands

X431 PAD V has guided functions among all online products of LAUNCH.

Guided Functions show all specific operating instructions step by step, and automatically run the instructions to do the resetting, matching, coding etc.

You just need to follow the instructions and click complete/continue to do it.

It is a good assistant helping you to find a way during the car repairing.

NEW OPTIONAL FUNCTIONS (option functions)

1. X431 ADAS Mobile/PRO: When the adaptive cruise control module (ACCM), radar sensor or front bumper has been replaced or does not meet the maintenance calibration requirements, you need to perform “radar calibration” on your vehicle.

2. VSP600-Videoscop: helps technicians to check issues on unreachable area in a vehicle. With 6 levels light strength, technicians can easily adjust the brightness according to the environment.

3. TSGUN: a professional tire pressure diagnostic tool that integrates TPMS sensor activation, reading, learning and pro-gramming. It activates reading tire pressure information by receiving signals at low or high frequencies. Check for abnormal conditions in time to prevent tire pressure problems.

4. X-PROG3 Immobilizer: turn this X431 diagnostic scanner into a capable IMMO service tool, providing fast, easy, and intuitive k-ey pro-gramming for VAG group vehicles with 2/3/3.5 gen. IMMO, and most Asian cars with low-level antitheft systems; also to have completed IMMO & K-ey Pro-gramming (read & write 1200+ EEPROM and MCU chips, etc.) for VW/Audi/Skoda/Seat models manufactured after 2008 with 4/5/5.5/6 gen. IMMO system.

5. X431 PRINTER: Print out diagnostic data/ reports
O2-1 ScopeBox, Oscilloscope: to quickly acquire the circuit signal, and slowly display the waveform for better data analysis.

6. BTS360 Bluetooth Battery Tester:
to get a thorough test of the vehicle battery.

7. ADAS . ect

How we ship and where we ship?

  •  We ship merchandise worldwide using DHL UPS & GLS. products on obdcarstore.com can be ship from different worldwide warehouses locations,
    for Free Import Tax delivey adress country must be one of our actual warehouse locations
    - European warehouse (only countries part of European community)
    - USA warehouse (only USA)
    - UK warehouse (just UK)
    - Australian warehouse
    - Russia warehouseWe can ship to other countries not cover by our main warehouses,  but client have to pay import tax according to local customs.

How much I will be charged for import duty?

  • Countries cover by our warehouse are Free of Customs Import Taxes.
  • What is the handling time?
    we ship every order in 1 working day, usually takes between 3 to 5 working days , the close delivery address are from warehouse
    the fast delivery will be, also keep in mind courier delivers only between Monday to Friday. There is no courier service on the weekends.

What should I notice before shipping?

  • Please be sure your shipping address is correct. We will only follow your address listed at the payment for the shipment. Due to the secure reasons,
    we are not allowed the address change through email. We have no responsibility for a Incorrect shipping address.

How long until I receive my items?

  • If the items you ordered are in stock, we will give it to the courier before the end of the day. This means that you will get your order no later than 5 days.
    If the items you ordered are not in stock in our shop, then it takes about 2-3 weeks to get it to you, provided the item is in stock with our supplier.
    If this is not the case, we will provide you with an estimated delivery time.

How will I know the delivery time?

  • As soon as the order is ready to be shipped, you will get a tracking code which will provide you with an ETA. For large items, we will notify you as soon as the order is ready and make an appointment that best suits your schedule.

If I buy several items, will they be delivered together?

  • If you order more than one item, we will do our best to send everything together.
    We like to consider the environment,
    so if you are not in a hurry for a specific item, we will send everything in one shipment once we have the complete
    order ready (unless there is an item with an extraordinary delivery time).

Further Questions

  • If you have any further questions regarding shipping or any other subject, please feel free to contact us and we will be happy to assist you.

Warranty – 1 Years
Updates – 2 Year Free Update

Reviews

There are no reviews yet.


Only logged in customers who have purchased this product may leave a review.